This Ruland setscrew shaft collar is made of aluminum. It really is a setscrew-type shaft collar for applications assisting low axial loads and simple positioning. Setscrew collars have improved holding power when the shaft materials is softer than the setscrew material. It really is made of aluminum for level of resistance to corrosion and tarnishing and is usually lightweight for make use of in applications where materials weight is a factor. This collar comes with a forged setscrew for securing the collar onto the shaft. The operating temperature ranges for this collar range from -40 to 107 degrees C (-40 to 225 degrees F). This shaft collar is suitable for use in various applications, including in the automotive industry to situate parts in vehicle power steering assemblies, the manufacturing industry to locate components on a conveyor belt system, and the hobby craft market to hold tires on axles in handy remote control vehicles, among others.
Shaft collars are ring-shaped devices primarily used to secure parts onto shafts. They also serve as locators, mechanical stops, and spacers between additional components. The two simple types of shaft collars are clamping (or split) collars, which come in one- or two-piece designs, and setscrew collars. In both types, one or more screws hold the collars set up on the shaft. In setscrew collars, screws are tightened through the collar until they press directly against the shaft, and in clamping collars, screws are tightened to uniformly compress the collar around the shaft without impinging or marring it. Setscrew collars and one-piece clamping collars should be set up by sliding the collar over the end of the shaft, while two-piece clamping collars separate into two halves and will be installed between elements on the shaft. Shaft collars are made from a wide selection of materials including zinc-plated steel, light weight aluminum, nylon, and neoprene. Found in nearly all sorts of machinery and market, shaft collars are used in applications including gearbox assemblies, motor bases, machine equipment, drive shafts, agricultural implements, medical gear, and paper and steel mill equipment, amongst others.
Ruland manufactures shaft collars, rigid couplings, and zero-backlash motion control couplings including beam couplings, bellows couplings, Oldham couplings, curved jaw couplings, and miniature disc couplings. The company, founded in 1937, and headquartered in Marlborough, MA, complies with Restriction of Hazardous Substances (RoHS) and Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH) standards.
· Setscrew shaft collar for applications supporting low axial loads and basic positioning
· Effective on shafts manufactured from softer material than the setscrew material
· Aluminium for resisting corrosion and tarnishing
· Includes a forged setscrew for securing the collar onto the shaft
· Operating temperatures range between -40 to 107 degrees C (-40 to 225 degrees F)
When you require to replace your existing flagpole flash collar this 2 piece collar makes installation easy. You don’t need to remove the pole or to go over the very best of the pole. This 2 piece cast light weight aluminum collar has a hidden hinge underneath the collar so no rivets or screws are in view.
The heavy-duty 2 piece Cast Aluminum Collars is the the majority of durable collar offered on the market today! Cast from Aluminum Alloy, 
these 1/4″ thicker cast collars are created to endure the harshest of conditions. replacement or addition to an existing flagpole.
I.D. around 1/8″ wider than Butt Diameter.
Light weight aluminum Decorative Pipe Collar – 5 inch Gasoline Type: Gas, Liquid Propane. Inner Diameter: 5″. Width: 10.625″. Double Wall Construction. UL Detailed. This Decorative Pipe Collar for 5 ” Type B Pipe from the Round Gas Vent series is usually a sort B gas component and consists of the duralock program for a good seal. This pipe collar is an optional accessory. It is to be utilized for decorative purposes. EPT Type B Gas Vent is made to meet the rugged demands of the job site. The inner wall is recessed to remove damage in handling. EPT’s innovative system for a lock-limited connection for Type B Gas Vent called DuraLock. Start to see the alignment indicators fulfill; feel the ends grasp jointly; hear the snap as the connection firmly locks into place. Type B gas vents aren’t suitable for use with wood-burning or coal applications, commercial ovens, exhaust ranges and hoods, grease or pollution ducting, or as free-standing up exhaust vents for high temperature applications. Type B Gas Vent provides been engineered to high temperature up rapidly. It remains hot through the operation of the appliance with minimal condensation in the applying and vent system. Pipe lengths can be found in multiple lengths, 6 to 60 ins, with a full complement of adjustable and rigid fittings. Looking for Simpson Dura-Vent? You found it! Simpson Dura-Vent has transformed their name to EPT. EPT is a recognized technological innovator in the venting market. Consistently the first ever to marketplace with new innovations in venting systems, EPT offers captured a leadership position in emerging marketplaces. EPT provides patents for several products and continues to design secure and technologically advanced venting. The company’s research into solving issues with corrosion, when biofuels such as corn are used, led to the break-through patent for PelletVent Pro. Scientifically confirmed components and unequalled engineering make EPT items not only the best option, or safest choice, however the only choice for professional quality venting products.
When you need to displace your existing flagpole flash collar this 2 piece collar makes installation easy. You don’t need to remove the pole or even to go over the very best of the pole. This 2 piece cast light weight aluminum collar has a hidden hinge underneath the collar therefore no rivets or screws are in view.
The heavy-duty 2 piece Cast Aluminum Collars is the the majority of durable collar offered on the market today! Cast from Light weight aluminum Alloy, these 1/4″ heavy cast collars are created to withstand the harshest of environments. replacement or addition to an existing flagpole.
Our spun light weight aluminum flash collar can be an ornamental covering that adds a finished turn to underneath of the flagpole. It also conceals and helps defend your floor sleeve from the components. Prices demonstrated below are for the standard bright satin complete. Our flash collars are also available in anodized and other finishes upon demand. Please call for availability and pricing.
The Design B Spun Collar is our most popular style flash collar for shoe foundation flagpoles and is manufactured to exacting specs from the best quality components. This flash collar provides the perfect finishing contact for your flagpole. For Use With Shoe Base Flagpole Applications